Dyna 3000 Switch Settings

Written by Jim Travis

Thursday, 10 June 2004

Dyna 3000 Switch Settings

Reprinted by permission, from Road Star Magazine

If you have installed a Dyna 3000 on your Road Star there is a little tip about how you can cut a hole in your battery case so you have easy access to the dip switches to change the Dyna's settings. Problem is, after doing this you can't see the mud map for the switch settings. So thanks to Jimtec of the Road Star Riders Forum here is a photo of the back of a Dyna 3000 for you to refer to or print out.

THE CURRENT SETTINGS IN THE IMAGE MAY NOT BE THE RECOMMENDED SETTING
FOR YOUR ROAD STAR, THE IMAGE IS ONLY A GUIDE

Click on the image for a larger version then print it out

Questions should be asked in our forum (Use discuss link below). The forum is very active and you stand a good chance of getting your questions answered there. If you would like to leave feedback for the author, or have additional information you think will benefit others, please use the comment section at the bottom of this page.

Discuss this article on the forums. (5 posts)

DISCLAIMER: This information and procedure is provided as a courtesy and is for informational purposes only. Neither the publishers nor the authors accept any responsibility for the accuracy, applicability, or suitability of this procedure. You assume all risks associated with the use of this information. NEITHER THE PUBLISHERs NOR THE AUTHORs SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION. Any type of modification or service work on your motorcycle should always be performed by a professional mechanic. If performed incorrectly, this procedure may endanger the safety of you and others on your motorcycle and possibly invalidate your manufacturer’s warranty.

Quote this article on your site | Views: 39670

Comments (10)

Ryan 3000 mistake
Written by RPCO, on 03-23-2016 21:46
Auto spell and not looking at what I bought....
The questions about setting is for a speedster ...not a dynamic or a Ryan....the again for any help you can suggest
Ralph in Boston

Ryan 3000
Written by RPCO, on 03-22-2016 21:48
I bought a used Ryan 3000, not sure how to figure settings ?
Is there a factory setting? What determines the settings ?
I have hyper properly jetted with slingshot unhandled....any suggestions ? The Ralph in Boston
2001 1600

best setting dyna 3000. 108cu in high co
Written by TEMPEST, on 09-23-2014 12:13
2005 high compression 108 cu in patric racing motor balanced crank (Falcone),ported intake , and 42mm patric carb . with bassani duals . any recommendations for the dyna ignition settings .?
I was noticing that on the dyna site they recommended b settings for high compression . ? I'm noticing that most are opting for the 34a setting and 5000 rpm . this bike of mine has the stock cams .I haven't called dynatek yet but that may be my next option. I have always liked talking to you guys abut the fixes for the roadstar , you all have been so helpful in the past.

Written by joe q, on 06-19-2012 11:16
how hard is it to raise rev limit on late models fuel injected motors .Dynatek came out with a module but it looks different than the earlier models I think it has to be programed with a computer not sure if I should bother D3K7-10 is the module #

Dyna vs Speedstar
Written by Starider, on 02-22-2010 16:24
OK I was ready to get the dyna 3000 when I heard about the Speedstar ignition now I'am confused. Im tired of hitting the rev limiter. After 10 years and 35000 miles I cant take it anymore.... yes I am a patient guy. Im lookin for some imput on which to choose. I have a set of VH long shots, Hyper charger and I believe a stage 2 jet kit. I would really appreciat any and all imput. Thanks in advance

Written by 02 road rider, on 03-18-2009 02:46
I have the high comp pistons and I have mine set at 3 I have a little spiting but runs good.

Written by heferwiz57, on 07-21-2008 20:20
My passing lamps went out on 06 RS Silverado. What is the deal?

dyna 3000
Written by cruzertim, on 04-23-2007 14:38
If you go to Dynatech's website www.dynaonline.com you will find that only the 2005 Roadstar has the passing lamp problem.

dyna 3000
Written by maddog200_0, on 02-14-2007 11:05
If you have add H/C piston,s where would the best setting be at on your Dyna 3000?
All so does the Retard switchs need to be set?

dyna 3000
Written by Wildstar1600, on 02-02-2007 18:57
I have a 2002 wildstar.do somone have picture of mounting it :roll

Only registered users can write comments.
Please login or register.

...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... -->

Tech Articles

Handlebars + Controls

License Plates

Lubrication

Luggage/Pouches

Misc Technical Papers

The Road Star Clinic is a collaborative community of riders who archive and publish user contributed technical data about Yamaha Road Star motorcycles.