EDITORS NOTE: Barry just started making a very cool gas cap option for the Road Star. If you would like to see it, please visit his website. It can be found on our "Links of Interest" page, or by clicking here. To email Barry, click on his name at the bottom of this article. -Thanks Barry! -GRAM
First thing I noticed when I got my new Road Star was the uncomfortable position of the floorboards. The rear of the boards was too high, raising my heel and making the calf of my leg sore.
I know there are floorboard extensions that move the board forward and tilt it at an angle. But what about those of us that are under 6 feet tall? I am only 5’10” and have a 29” inseam. Well those extensions certainly won’t work for me. It’s like trying to reach the pedals of a 26” bicycle when I was 9 or 10 years old.
Well let me show you an idea that might work for you. It will take some grinding and an hour or two of your time.
1. First let me show you the position of the mounting holes on the floorboards. There are two 3/8” spacers welded to the back of the holes in the floorboard mounts.
It’s kind of a trick photo since I do not have a picture of the bracket before I removed the spacer.
2. The spacer on the rear hole must be removed without damaging the spacer. Grind the welds off and as close to the spacer as possible. You might have to use a chisel to break away the last part of the weld on the shoulder. Pic #2 shows the weld that has to be removed on the rear spacer.
Weld that has to be ground away on the rear spacer.
3. Now with the spacer removed, elongate the hole with a round grinding stone, such as a Dremel or Rotary Pneumatic Grinder. (PIC #3)
Rear hole elongated.
4. Now you can install the floorboard and manually install the spacer behind the hole and screw the mounting bolt through the elongated hole, through the spacer in into the mounting threads. You can start to see the angle you can achieve in the picture. (PIC #4)
5. Now you can mount the boards and since the rear brake assembly on the right side and the shift mechanism on the left side there are clearances that might have to be adjusted to get the full tilt that you would like to achieve.
In the following pictures, (PIC #4 and PIC #5) will show the before and after.
PIC #4 Stock position
PIC #5 After adjustment
The best I can tell is that you can achieve about a 15 to 20 degree tilt. AND IT DOESN’T COST A SINGLE PENNY.
Good Luck and hope you enjoy!
Contact Barry “GlockerDude” Boyer if you have any questions. Barry@Boyer.net
Questions should be asked in our forum (Use discuss link below).
The forum is very active and you stand a good chance of getting your questions
answered there. If you would like to leave feedback
for the author, or have additional information you think will benefit others, please use
the comment section at the bottom of this page.
Discuss this article on the forums. (0 posts)
This information and procedure is provided
as a courtesy and is for informational purposes only.
Neither the publishers nor the authors
accept any responsibility for the accuracy, applicability, or
suitability of this procedure. You assume all risks associated
with the use of this information. NEITHER THE PUBLISHERs NOR THE AUTHORs
SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY
CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION.
Any type of modification or service work on your motorcycle should
be performed by a
If performed incorrectly,
this procedure may
endanger the safety of you and others
on your motorcycle and possibly
invalidate your manufacturer’s warranty.
Quote this article on your site | Views: 22677
|Floor board tilt|
Written by Uncle_B_Bear, on 03-23-2010 17:57
Great idea , Thanx , My 28 inch inseam will appreciate that.... soon as I can find a set of floor boards and foot gear to replace my forward controls that are going to need wooden blocks... LOL
|Written by dmfarms, on 05-26-2008 10:36 |
I was looking for a way to do this also, just to make it more comfortable, thanks GlockerDude this is a great idea
Only registered users can write comments.
Please login or register.
Powered by AkoComment Tweaked Special Edition v.1.4.6
AkoComment © Copyright 2004 by Arthur Konze - www.mamboportal.com
All right reserved