Swapping your pillion's footpegs will give most
passengers a greater degree of comfort. It is an easy mod to do and will
only take about ten to fifteen minutes. Please note: this mod will
not work with the stock exhaust pipes, at the end of these instructions there is a list of known
exhausts that it will work with. If your exhaust is not listed, give it a
try anyway, it only takes a few minutes to put it all back together.
Remove the bolts
- First remove the footpegs from each side of the bike, you will
need a 5mm Allen key for this.
Test clearance for your exhaust
- Before you do anything else, check that the left side footpeg
will fit on the right side of the bike in an upside down position (you don't
have to bolt it on, it was just easier to take the picture).
- If your exhaust interferes with it, or the exhaust is too close
then put the pegs back on the way you took them off and be done with it.
If it checks out then put the right footpeg on the ground on the left hand
side of the bike and vice versa (saves a little confusion later).
- Next you have to turn the footpegs themselves 180
degrees in their bracket, if you don't, you'll find that when a pillion's
foot is put on them they will want to fold down instead of being locked in
position, which is very dangerous for obvious reasons!
Remove the locking pin
- Using a pair of pliers, remove the locking pin from the shaft
that holds the peg to the bracket.
This is bad, you want the
locking pin facing down
- Twist the footpeg 180 degrees and re-insert the shaft, making
sure that the top of the shaft will face the sky when the footpeg is in position
so you have a nice clean looking install, NOT like the image attached.
Push on top of the bracket to
shaft in place
- To get the shaft in place put the tip of the footpeg on
your knee, and then push down on top of the bracket with your hand so the
footpeg compresses enough to get the shaft back in position.
- Now all you have to do is bolt the footpegs back onto the bike
in an upside down position, they don't have to be too tight although if you do
have a torque wrench set it to 11ft/lb (Yamaha Workshop Manual recommendation
for M8 bolt)
- Your done!
This mod WON'T work with the stock
This mod is known to work with the following
- Baron's Nasty Boys
- Bub's Big Willeys
- Bub's Chambermaids
- Bub's Stubbies
- DD Dual Sideburners
- Roadhouse 2-1's
- Roadhouse Dooleys
- V&H Longshots (with longer bolts and spacers)
- V&H 2-1
Copyright © by RoadStarMagazine.com All Right Reserved.
Questions should be asked in our forum (Use discuss link below).
The forum is very active and you stand a good chance of getting your questions
answered there. If you would like to leave feedback
for the author, or have additional information you think will benefit others, please use
the comment section at the bottom of this page.
Discuss this article on the forums. (0 posts)
This information and procedure is provided
as a courtesy and is for informational purposes only.
Neither the publishers nor the authors
accept any responsibility for the accuracy, applicability, or
suitability of this procedure. You assume all risks associated
with the use of this information. NEITHER THE PUBLISHERs NOR THE AUTHORs
SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY
CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION.
Any type of modification or service work on your motorcycle should
be performed by a
If performed incorrectly,
this procedure may
endanger the safety of you and others
on your motorcycle and possibly
invalidate your manufacturer’s warranty.
Quote this article on your site | Views: 24790
Written by mdougall, on 06-04-2013 16:51
Did the flip. Works well with Samson exhaust. My wife prefers it this way. She says is much more comfortable.
Written by caffinated1, on 01-30-2011 16:20
You can do this mod with the brackets on opposite sides, just need longer bolts and 1" spacers to clear the swing arm caps. Did it last year for my boy, he grew too much for the stock height to be comfortable.
I switched over though to this configuration for the wife.
|Written by JYD, on 12-27-2009 12:34 |
I want to do this mod just for the look,but my lady is 4'11" and can barely reach the stock pegs.Guess I`ll have to get a a new lady!(just kiddin).Good mod though
Written by Aussie B, on 03-02-2009 06:53
This works with Sampson Warlord Ripsaw.
Written by RoadstarB, on 11-19-2007 19:21
The peg flip will not work with my Bub BigWilly's exhaust. I noticed in the picture you must have the Chambermaid system, I think they hang alittle lower than mine.
Written by eirinn99, on 02-11-2007 19:01
works on cobra speedster longs too, but pegs comes really near the upper pipe
Written by Maxer4, on 08-31-2005 19:50
Also works with Cobra Speedster Shorts exhaust pipes. Much more comfortable for passenger.
Only registered users can write comments.
Please login or register.
Powered by AkoComment Tweaked Special Edition v.1.4.6
AkoComment © Copyright 2004 by Arthur Konze - www.mamboportal.com
All right reserved