<
 
 
 
 
×
>
hide You are viewing an archived web page collected at the request of Road Star Clinic using Archive-It. This page was captured on 18:40:56 Feb 23, 2018, and is part of the Road Star Clinic Closure collection. The information on this web page may be out of date. See All versions of this archived page. Loading media information

This is an archived version of the Road Star Clinic. The Road Star Clinic can now be found at www.roadstarclinic.com. Please join us there!

Quick Disconnect System for Silverado Bags

Print
User Rating: / 28
PoorBest 
Written by Dave McDougall (ZOOMER)   
Thursday, 10 June 2004

Reprinted by Permission from Mr Tidy's Tech Tips

Whenever I wanted to clean the bike up it was always a pain to have to unbolt the bags off the supports so I could clean in behind them. I thought of these pins and tried them out. Turns out they work great and it's now a snap to remove the bags for cleaning or for taking them inside while traveling.

All that's needed are 8- 6mm bolts that are long enough to provide the pin length needed, 8 small hairpins and 8- 6mm nuts. Any hardware store should have all of these items.

I screwed the bolts into the bag brackets and run the nuts up the threads on the backside to lock them into place. Now just measure the lengths according to the drawing and cut them off with a hacksaw. Clean the edges up with a file and drill the 3/32" holes in the top pins. You might want to mark the top pins and then remove them for drilling.

When reinstalling the bags you are going to have to push on the top of the bag to get the top pins to align with the holes in the bag. The bottom pins are only there to hold the bag in position and the top pins do the actual fastening of the bags. Use the large washers from the original hardware on the top pins and install your hairpin….Done.

I've been running with this setup for 31,000 kms with no problems or rattles. Hope someone can find this information useful.

      Dave McDougall (ZOOMER)

I think Dave did a good job here and it's all pretty self explained.  I don't have the Silverado Bags but if I did, I'd be using his setup...
Thanks Dave..

                                        Mr.Tidy



Questions should be asked in our forum (Use discuss link below). The forum is very active and you stand a good chance of getting your questions answered there. If you would like to leave feedback for the author, or have additional information you think will benefit others, please use the comment section at the bottom of this page.

Discuss this article on the forums. (0 posts)


DISCLAIMER: This information and procedure is provided as a courtesy and is for informational purposes only.  Neither the publishers nor the authors accept any responsibility for the accuracy, applicability, or suitability of this procedure.  You assume all risks associated with the use of this information.  NEITHER THE PUBLISHERs NOR THE AUTHORs SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION.  Any type of modification or service work on your motorcycle should always be performed by a professional mechanic. If performed incorrectly, this procedure may endanger the safety of you and others on your motorcycle and possibly invalidate your manufacturer’s warranty.


Quote this article on your site | Views: 26878

  Comments (6)
So simple and what a savings!
Written by mbourbeau12, on 12-27-2013 17:32
Just completed my quick disconnects and save a bunch of money. Between these saving and what I saved by switching to GEICO I should be able to purchased a new part or mod for the bike. Again thank you for the step by step.
org dimensions bolts in rear fairing
Written by Foosi, on 06-15-2013 04:00
I'm drilling holes in my rear fender for mounting org saddlebags again. rear fender rebuilt sometime. 
Can someone tell if its a 8mm för the original holders ?  
I found a pair of bags on the "market" for only 80$
Good ideas spark others
Written by lakeczar4, on 08-23-2008 08:01
I read with great interest the article on the quick release system. If you can find them, get 4 star or knurled knobs that have 6 mm studs on them. Use just the studs on the bottom (or get four and use them on all points), as in the original modification.Use the star knobs on the sides and you can quickly spin them out to take your bags off. Works even on the hard bags. Also eliminates anything catching or scratching on the hairpins when you load or unload the bags. Most hardware stors carry the star knobs, some carry the metric version. Watch out for the caged idiots.
hard bags
Written by shorty, on 07-12-2008 09:16
this system works with the hard bags just pull the spacer out of each rubber gromit ang set yhe bag over the studs and then push the spacer over the studs works great
Quick Disconnect System for Silverado Ba
Written by FourFingers, on 05-22-2008 06:43
I have the ultimate solution to the quick disconnect,it only takes about 5seconds for each bag.I used half of Dave's idea and was wondering if you don't mind that as soon as I have figured out how to post the pictures tha I can use it? 
Thanx 
Don
My mistake...
Written by stardust, on 07-31-2007 22:29
Good system Dave. Wish I'd looked a little closer and noticed the soft bags. At least I only made the pins up for one side and tried it out only to discover that you can't force the Silverado Hardbags on there. 
I'm going to use the top pins and the allen head bolts on the bottom so it'll help a little anyway. All is not lost. 
 
Bob

Only registered users can write comments.
Please login or register.

Powered by AkoComment Tweaked Special Edition v.1.4.6
AkoComment © Copyright 2004 by Arthur Konze - www.mamboportal.com
All right reserved

 
...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... -->

The Road Star Clinic is a collaborative community of riders who archive and publish user contributed technical data about Yamaha Road Star motorcycles.

Copyright 2003-2007 Road Star Clinic and its respective authors.
<-- -->