Reprinted by Permission from Mr Tidy's Tech Tips
|So you ordered the wrong height windshield, and now you have to sit on a pillow to see over the top? Well good friend, let's try to fix that.
|Following is a method we all can use to cut down the height of our windshield , and still make it look "Factory Fresh".|
First, determine the exact amount needed to remove. The best method is to place a "band" of blue masking tape with the top edge where you think you want to cut.
Make the band of tape at least four inches high, so that you cannot see under the bottom of the tape.
Now take a ride !! A good long one !! Keep the tape on for a few days if necessary. You will find that after a few minutes you "settle in the saddle" , which gives you a more accurate idea of how much to cut. I learned this the hard way and ended up cutting my shield three times before I was satisfied.
|On a piece of cardboard, trace the shield's top outline.
Cut this outline out from the cardboard.
|Place a 2" wide strip of blue masking tape on the INSIDE of the shield, centered over where the cut will be.
Use the cardboard pattern to trace a "Cut" line on to the tape.
|The shield will be cut with the front side of the shield down on the bandsaw table top. If using a Saber saw, cut from the front side of the shield with the inside down.
The curved front of the shield must be covered to protect from scratches.
I usually cover with a thin cardboard or heavy plastic bags. Anything to prevent scratched.
Many will disagree but almost any type of saw blade will work. Most shields are tough Polycarbonate plastic (Lexan) which does not crack, chip, or scratch too easily.
I use a "Six teeth per inch" wood blade on my bandsaw. A finer blade demands less sanding but I am too lazy to change blades.
Cut on the line, using as smooth a motion as possible so as to reduce the sanding chore.
|Here is a very important hint :
Sand the edge round (like the rest of the shield) WITH THE SHIELD STANDING UPRIGHT !!
If you lay it down the plastic dust will cause scratches where it contacts the table.
Use 80 grit paper in a palm sander then switch to 220 for a "Fairly" smooth finish. This job can also be done by hand using the sandpaper on a piece of wood 2 x 4. Just get a smooth finish with a curved edge that is the same as the rest of the shield.
|The final step that produces that "Factory" edge is sort of delicate. If you slip here you will have a spotted shield!
Most hardware stores sell M.E.K. (methyl ethyl keytone) as a universal solvent. This stuff "Melts" plastic. Moisten a COTTON rag just big enough to wrap over your index finger. Get it very wet, but not dripping. With a steady motion, wipe the newly sanded edge in one smooth stroke. WOW !!! It turns clear !!
If necessary , wait a few minutes and do it again. The plastic dries almost immediately.
I suggest you practice the "Wipe" on the piece you cut off. It really is easy , as long as you don't drip.
That's it ! Simple, but do it right the first time. And don't sniff too much of that M.E.K. !
Questions should be asked in our forum (Use discuss link below).
The forum is very active and you stand a good chance of getting your questions
answered there. If you would like to leave feedback
for the author, or have additional information you think will benefit others, please use
the comment section at the bottom of this page.
Discuss this article on the forums. (2 posts)
This information and procedure is provided
as a courtesy and is for informational purposes only.
Neither the publishers nor the authors
accept any responsibility for the accuracy, applicability, or
suitability of this procedure. You assume all risks associated
with the use of this information. NEITHER THE PUBLISHERs NOR THE AUTHORs
SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY
CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION.
Any type of modification or service work on your motorcycle should
be performed by a
If performed incorrectly,
this procedure may
endanger the safety of you and others
on your motorcycle and possibly
invalidate your manufacturer’s warranty.
Quote this article on your site | Views: 46073
|Written by Horsehammerr, on 02-01-2015 07:00 |
I'm pretty anal about altering stock parts that CAN NOT be returned to original. I do alot of research up to decision making. This one was just as tense. After a few days of research and measurements I made all my cuts out of the bottom of the OE windshield. Dropped it 6 1/2" and now the top is exactly center of my nose. PERFECT !!
Written by ZoomZoom, on 06-21-2010 13:37
Can I use a dremel tool to cut the windshield?
Written by Moe, on 03-27-2008 08:32
Good day everyone, I have a simple question, where exactly do you measure the height of a windshield so when I do order one I won't get one to small or to big, thanks.
|Written by THE HAG, on 02-05-2008 12:54 |
I cut the bottom of my windshield rather than the top, eazy to move the large chrome panels up one hole and use a roto-zip to follow along the bottom, this way you retain the factory edge on the top and the unused holes are hidden or cut off, then just sand the edges smooth.
Only registered users can write comments.
Please login or register.
Powered by AkoComment Tweaked Special Edition v.1.4.6
AkoComment © Copyright 2004 by Arthur Konze - www.mamboportal.com
All right reserved