<
 
 
 
 
×
>
hide You are viewing an archived web page collected at the request of Road Star Clinic using Archive-It. This page was captured on 18:45:50 Feb 23, 2018, and is part of the Road Star Clinic Closure collection. The information on this web page may be out of date. See All versions of this archived page. Loading media information

This is an archived version of the Road Star Clinic. The Road Star Clinic can now be found at www.roadstarclinic.com. Please join us there!

Failed Parts to Watch for

Print
User Rating: / 40
PoorBest 
Written by Mr Tidy   
Saturday, 05 March 2005
Frame shock mount : This has happened several times so it is an area you want to pay attention to for periodic inspections. Inspect from underneath bike between rear wheel and engine.

 

 
Rear Wheel Hub:  Pay attention to a faint popping or clicking noise when rolling bike with engine dead. Most will notice it when backing bike 
out of their garage or storage building a faint popping or thud.  These failures are occurring on
low and high mileage wheels.
Although this is just one possible cause,  it is very easy to check for when replacing a rear tire.
Notice the ridge formed inside the drive side of
the hub, this is where one of the 4 wheel bearings
rides in the hub.  In the picture to the right you'll
notice the bearing that is visible, it has also 
wallared out the hub as well.

What to check for:  A pop, click, faint thud when rolling on bike with engine dead as in rolling to a stop or backing the bike out of garage or storage shed, a wheel bearing that falls out when removing rear wheel.

Oil Pump Shaft:  The picture on the left shows the oil pump shaft Yamaha used for the Road Star in models previous to 2002.  The oil pump shafts on the right are the early model.  The one on the left is the new model.  It is a duplicate of the one used in the Warrior.  There have been some reports of early oil pump shafts braking in the thin area at the top, and subsequently causing very serious engine damage due to lack of oil circulation in the engine.  Many dealers are not aware of this problem.

Thanks to Paul Pierce for supplying the picture



Questions should be asked in our forum (Use discuss link below). The forum is very active and you stand a good chance of getting your questions answered there. If you would like to leave feedback for the author, or have additional information you think will benefit others, please use the comment section at the bottom of this page.

Discuss this article on the forums. (0 posts)


DISCLAIMER: This information and procedure is provided as a courtesy and is for informational purposes only.  Neither the publishers nor the authors accept any responsibility for the accuracy, applicability, or suitability of this procedure.  You assume all risks associated with the use of this information.  NEITHER THE PUBLISHERs NOR THE AUTHORs SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION.  Any type of modification or service work on your motorcycle should always be performed by a professional mechanic. If performed incorrectly, this procedure may endanger the safety of you and others on your motorcycle and possibly invalidate your manufacturer’s warranty.


Quote this article on your site | Views: 47354

  Comments (6)
Written by stilltrying, on 04-18-2015 17:54
My speedo, trip meters, odometer and turn signal cancel features have all stopped working. 
Gas gauge seems to be o.k. Any ideas as to possible cause?  
 
Marcd65@yahoo.com
Engine will not start
Written by dannyb661, on 10-14-2012 13:55
Just replace battery, checked all fuses, turn ignition, lights on, gauges activate, neutral. When pressing ignition start lever, i hear clicking noise, nothing else. What could it be? 
 
Thank you.
Oil pump shaft
Written by roadawg, on 08-28-2012 09:45
My 2000 RoadStar is getting a new oil pump shaft. Why? Turns out if you idle your engine too low as to let the engine lobe like a Harley engine, the oil pump shaft does an inadequate job of lubing the engine. On mine, the hydraulic lifters failed and I need a new oil pump. Save yourself the $500 fix and make sure the idle is set correctly. Hope this helps anyone else with this issue.
Air filter after market
Written by harley, on 04-22-2012 15:09
hi would I open up the motor a bit if i pot in a kuryakyn hypercharger air filter with out any other modes. My bike is stock 
 
Thank you
Great info
Written by EL PASO KID, on 11-18-2011 05:53
Great info have a fellow rider who has the clicking noise never would have guessed the problem.
Appreciate the information
Written by Braveheartz2, on 07-20-2011 21:02
:) Great information - thanks!

Only registered users can write comments.
Please login or register.

Powered by AkoComment Tweaked Special Edition v.1.4.6
AkoComment © Copyright 2004 by Arthur Konze - www.mamboportal.com
All right reserved

 
...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... ...................................................................... -->

The Road Star Clinic is a collaborative community of riders who archive and publish user contributed technical data about Yamaha Road Star motorcycles.

Copyright 2003-2007 Road Star Clinic and its respective authors.
<-- -->