Page 5 of 5
Finishing the Installation
If you have not installed a new starter, inspect the starter's terminal-post to be sure it is free of corrosion and dirt; clean as needed.
To connect the new cable to the starter do the following:
- Be sure only one nut is on the starter's terminal-post.
- If you're installing a Warrior starter, check the post. It should have a rubber O-ring, and two brown plastic (dielectric) washers at its base. The washers should place the lower nut high enough so it won't touch the starter case.
- If you're installing a stock starter, check the post. It should have two brown plastic (dielectric) washers at its base. The washers should place the lower nut high enough so it won't touch the starter case.
- Snug the lower nut down against the washer(s) at the base of the post. If you skip this, the post may come loose.
- Slip the rubber boot onto the cable.
- Put the cable end on to the post.
- Install and tighten the upper nut, while holding the lower nut using an open-end wrench. Do not use thread-lock, as you want to ensure a good electrical connection. Instead, just be sure you've got the nuts good and tight (but not excessive).
- Apply some dielectric grease to the post and nuts to inhibit corrosion. Note: Do not use excessive grease, as it can seep into the cable and discolor the look, if you are installing transparent coated cables.
- Pull the boot down over the post and nuts.
See the completed installation in the photo below.
If you removed the battery, reinstall it now.
After inspecting for corrosion, reconnect the positive (left side) battery cable. Remember to smear on some dielectric grease.
Then connect the negative (right-side) lead. Remember to smear on some dielectric grease.
Now turn on the ignition and hit the starter button. The starter should be noticeably more powerful--especially if you installed the Warrior starter.
If the starter won't engage at all, be sure your transmission is in neutral.
If it doesn't spin the engine with more authority, check your connections for a loose bolt or nut. Also try removing the bolts/nuts, cleaning the terminals and fasteners again, and then re-tightening them.
If, after thoroughly searching for a poor connection, you still have little, or no, starting power, you can suspect the starter or the battery. To test them, do the following:
- Turn on the ignition.
- If the lights don't shine brightly, the battery terminals may not have good connection.
- Turn off the ignition.
- Detach the new cable from the starter, and temporarily bolt one end of the stock cable to the starter post. (Be sure the stock cable ends are clean).
- Be sure your transmission is in neutral.
- While protecting yourself from electrical shock with thick rubber gloves or other insulation, touch the other end of the stock cable to the positive (left) side of the battery.
- The starter should immediately spin.
- If not, and yet the lights come on with the ignition, the starter may be bad.
You can also try this test again, using your stock starter--reinstalled.
Once everything checks out, just put the left side-cover back on and smile. You’ve done something very good for your bike.
Questions should be asked in our forum (Use discuss link below).
The forum is very active and you stand a good chance of getting your questions
answered there. If you would like to leave feedback
for the author, or have additional information you think will benefit others, please use
the comment section at the bottom of this page.
Discuss this article on the forums. (0 posts)
This information and procedure is provided
as a courtesy and is for informational purposes only.
Neither the publishers nor the authors
accept any responsibility for the accuracy, applicability, or
suitability of this procedure. You assume all risks associated
with the use of this information. NEITHER THE PUBLISHERs NOR THE AUTHORs
SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY
CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION.
Any type of modification or service work on your motorcycle should
be performed by a
If performed incorrectly,
this procedure may
endanger the safety of you and others
on your motorcycle and possibly
invalidate your manufacturer’s warranty.
Quote this article on your site | Views: 65314
|4 gauge starter wires|
Written by Newf1, on 02-15-2017 07:55
great information , if you need any assistance on fixing anything on your (Roadie) this is the place to look ROAD STAR CLINIC.
|OEM Part numbers please?|
Written by Starjunkie, on 01-17-2014 10:24
Could I get the OEM yamaha part numbers for the solenoid and starter please? Thank you. Jeff
Written by Jeephed, on 05-15-2013 20:05
I was having an issue with my starter where it would turn over once, wait a few seconds then turn over again and start the engine. I figured I would need to replace the starter. I started with the wires first since it was cheaper.
Like night and day now, it rarely does the hesitation start any more.
One thing I had a problem with was the Warrior relay. I didn't know it was reverse wired to the batt.
|Written by yamaleidy, on 08-28-2012 23:36 |
I don't even open my owners manual anymore,I come straight here. I am now ready to tackle this job. Thanks
|Written by Lazydog, on 10-18-2009 21:54 |
great piece. I'm experiencing starter problem where it won't start but wires and motor get hot. What about the various relays. Don't they play a part??
Written by BrooklynBiker, on 05-01-2009 03:12
RANDY,YOU ARE THE BEST,KEEP UP THE GOOD WORK.
THANKS, BIG JIM
Written by chromepony, on 03-15-2009 19:14
I just finished the cable install on my '00 R/S. I stayed w/the stock starter,but put a kit[(new brushes)$60] in it while I had it on the bench. Don't know if it's the cables or the fresh starter or (probably) the combination of the two,but the starter almost spins the motor out of the frame when I bump the button now. Time & money well spent.
|Great, Great article|
Written by TChaap, on 02-14-2008 18:59
This is just an outstanding article. This install is not rocket science but it sure does give a novice like me a lot of confidence to tackle something they want to fix. The details were super. Thanks for your time.
|No longer available?|
Written by nazuma, on 11-11-2007 14:25
Can't seem to find the custom starter cable kit on the bulldog website.
Recommend anything else?
If not, what is the length?
Written by flashback, on 10-13-2007 16:16
Randy, this is a great article, Iv'e only had my bike a short time but have always felt the starting circuit was a bit aneimic. It is something I have on my list but did not know if anything was available.. Thanks...
Only registered users can write comments.
Please login or register.
Powered by AkoComment Tweaked Special Edition v.1.4.6
AkoComment © Copyright 2004 by Arthur Konze - www.mamboportal.com
All right reserved