Assembling the Generator Area |
Written by Randy Fox | ||||
Saturday, 03 November 2007 | ||||
IntroductionThis article is one of a series that describes how to disassemble, work on, and reassemble the Road Star engine. This particular article explains how to install the generator assembly. See the Complete Engine Tear Down, Orientation article in this website for details. Be sure you refer to the service manual through all phases of this project.
Installing the Generator Bolt and Cover![]()
First, fold over a copper washer. Wedge it between the lower teeth of the primary drive gear and the clutch-housing gear (a.k.a. clutch basket). This will lock them. Put on the generator shaft bolt and washer from the engine's left side. Tighten the bolt using 20 ft-lbs of torque. Refer to the service manual for details. Remove the copper washer! Install the generator shaft cover (two bolts) with O-ring. Use 7.2 ft-lbs of torque, which is 86.4 in-lbs.
Installing the Starter![]()
Now lubricate the O-ring on the new starter with a bit of engine oil. Then using both hands again, slide the starter into the engine housing. Wiggle the starter as you go, to help the starter gear engage with the engine gears. As the O-ring nears its ‘home’, it will become tight again. You can stop pushing at this point. Then insert the two mounting bolts into the starter mount, and torque them to 7.2 ft-lbs. The starter O-ring seal will be pushed ‘home’ as you tighten the mounting bolts. Installing the Stator and Generator Cover AssemblyNow is a good time to clean the generator cover gasket surfaces of old gasket remnants. Do this for the gasket surface of the engine case, as well as the generator cover. Be sure to wipe up any particles that may fall in. Be sure you clean off all silicone remnants from the oil seals and cover, too. If you separated the oil delivery pipe from the generator cover--for some reason--bolt them back together. Be sure both ends of the oil delivery pipe have their O-rings installed.
If you removed the stator from the inside of the generator cover, do the following:
Finishing the Generator AssemblyInsert the two alignment dowels for the generator cover into the engine case. Then slip a new gasket over the dowels. Tip: The generator cover is magnetized to the generator rotor. As soon as you begin installing the cover, it will be sucked in by magnetic force. Bolt and torque the generator cover on, using 7.2 ft-lbs, which is 86.4 in-lbs. The long bolt nearest the oil delivery tube has a copper or aluminum washer. I recommend you install a new washer at this point. I didn't, and it leaked. Bolt and torque the oil-delivery-pipe back into its hole in the right-side of the engine case, using 7.2 ft-lbs of torque, which is 86.4 in-lbs. Again, be sure it has its O-ring installed. See photo below.
Now run the stator wires back into the corrugated wiring tube. Pull the wires through the tube. Then route the wires behind the rear of the engine, and up to the point of connection under the side-cover area, near the bike’s center. Smear some dielectric grease into the contact points of both connectors and then connect them.
Proceeding to the Next StepTo access related articles, refer back to the Complete Engine Tear Down, Orientation article in this series to see which additional articles best address your situation.
Questions should be asked in our forum (Use discuss link below). The forum is very active and you stand a good chance of getting your questions answered there. If you would like to leave feedback for the author, or have additional information you think will benefit others, please use the comment section at the bottom of this page. Discuss this article on the forums. (0 posts) DISCLAIMER: This information and procedure is provided as a courtesy and is for informational purposes only. Neither the publishers nor the authors accept any responsibility for the accuracy, applicability, or suitability of this procedure. You assume all risks associated with the use of this information. NEITHER THE PUBLISHERs NOR THE AUTHORs SHALL IN ANY EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, PUNITIVE, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OF ANY NATURE ARISING OUT OF OR IN ANY WAY CONNECTED WITH THE USE OR MISUSE OF THIS INFORMATION OR LACK OF INFORMATION. Any type of modification or service work on your motorcycle should always be performed by a professional mechanic. If performed incorrectly, this procedure may endanger the safety of you and others on your motorcycle and possibly invalidate your manufacturer’s warranty. ![]()
Only registered users can write comments. Powered by AkoComment Tweaked Special Edition v.1.4.6
|